Description
Hand Setter or Hand Press Machine Die Set for 12.5mm and 15mm Press Studs
Suits:
- 12.5mm press studs,
- 15mm press studs
for either hand setting these studs or using the hand press machine.
These setters suit the press stud fasteners either 15mm, or 12.5mm diameter
Description
Press studs also, known as Durables, are more heavy duty than snap fasteners
These are used on fabric, leather or vinyl, attached with a hand setter or die (hand press machine setter).
Each press stud has 2 parts to each side, the female parts are usually on the side of the article that will be seen, the flap or side that opens,
The ‘button’ (the outside, often the decorative part) and the socket is attached to the cap through the leather or fabric.
The stud and eyelet are usually under the flap or opening, on the under side, not normally visible.
The stud – presses into the socket to with a snap, and is held in place through the fabric or leather with the eyelet (base) post.
Both the male and the female snap fastener setters (also known as dies) have 2 parts each.
The biggest parts have a 19mm diameter shaft that slips into the base hole of the hand press machine,
one to hold the snap cap, and the other to hold the base post until set – holding the stud in place.
and the 2 threaded setter-dies easily screw into the threaded upper arm of the hand press machine,
and by pressing the handle down, this rolls the snap cap post over inside the socket,
holding it securely in place, and the other compresses the stud over the base post
It is very quick and easy to interchange between styles of setters and the sizes.
Hardest part of using these tools is being organised
And keeping parts in a spot easy to find for next time
Virtually no maintenance apart from maybe a light wipe over with light machine oil.
Hand Setters
Dimensions:
Hand setter for 12.5mm press stud
- The button setter – Total Height 20mm
- Base – diameter 24
- The socket setter
- total height 97.5mm
- diameter 12mm
- The stud die – Total Height 22mm,
- diameter 25mm
- The eyelet die – spring tipped
- total height 100.25mm
- diameter 14mm
Hand setter for 15mm press stud
- The button setter – Total Height 20mm
- Base – diameter 24
- The socket setter
- total height 98.4mm
- diameter 14mm
- The stud die – Total Height 26.5mm,
- diameter 24mm
- The eyelet die – spring tipped
- total height 100mm
- diameter 17mm
Hand Press Machine Die Set
Dimensions:
12.5mm press stud dies for HPM
- The button die – Total Height 28mm
- Base – diameter 21.6 narrow to diameter 19mm to fit into hole on the arm
- The socket die – silicone tip
- Threaded shaft diameter M8 8mm (screws into the thread hole of upper arm of the HPM)
- total height 32mm
- top diameter 16.3mm
- The stud die – Total Height 33mm, including sprung pin
- top diameter 21.4mm
- Base Shaft diameter 19mm (fits in the base hole of HPM)
- The eyelet die – silicone tip
- Threaded shaft diameter M8 8mm (screws into the thread hole of upper arm of the HPM)
- total height 32.4mm
- top diameter 12.8mm
15mm press stud dies for HPM
- The button die – Total Height 28mm
- Base – diameter 21.6 narrow to diameter 19mm to fit into hole on the arm
- The socket die – silicone tip
- Threaded shaft diameter M8 8mm (screws into the thread hole of upper arm of the HPM)
- total height 30mm
- top diameter 18.7mm
- The stud die – Total Height 33mm, including sprung pin
- top diameter 21.4mm
- Base Shaft diameter 19mm (fits in the base hole of HPM)
- The eyelet die – silicone tip
- Threaded shaft diameter M8 8mm (screws into the thread hole of upper arm of the HPM)
- total height 33mm
- top diameter 16mm
Base material
- metal